HISTORY
| 1980.07 | |
Established the DONG SEO CONTROL CO., LTD. |
| 1982.10 |
Appointed as a Cooperating Company by DAE WOO HEAVY CO., LTD. |
| 1983.12 |
Entered in the Korea machine Tool Manufactures' Association |
| 1986.06 |
Established the DONG SEO AIRCRAFT COMPONENT CO., LTD. |
| 1988.01 |
Appointed as a Bright Prospect Small Business by the Korea Development Institute |
| 1991.05 |
Established the DONG SEO AIRCRAFT Technology Research Institute
Registered as a Defense Industry Company |
| 1991.11 |
Appointed as a Military Exception Company by the Office of Military Manpower Administration |
| 1992.05 |
Registered in the Association of Aviation Company |
| 1992.08 |
Appointed as a Technology Advanced Company |
| 1996.08 |
Authorized by ISO 9002(Chapter AC-00273) |
| 1997.04 |
Received an award from the president of Korea |
| 1997.08 |
Change a Trade name to DONG SEO MECHATRONICS |
| 1998.07 |
Appointed as a Fifty Excellent Quality-Competitiveness Company
by the National Institute of Technology and Quality. |
SERVO LOW PRESSURE DIE CASTING MACHINE
FEATURE
This machine casts the Aluminum Alloy and all the system is operated automatically by computer. Pressing
a system that is most important in casting aluminum specially uses the way of PID Control by computer.
So any Air Leak or Pressure Variable can not influence it and works pressing by given data.
Servo Low Pressure Die Casting Machine is developed first in Korea.
In addition to its productivity, it has best quality and user friendly system. It is possible to
analyze products.
It can automatically manage the production. High quality can be produced and new Aluminum Alloy can be
developed. For example, Engine Head & wheel of motor cycles and passenger vehicles.
GENERAL SPECIFICATION
| ITEM |
SPECIFICATION |
| Static Die Plate |
100mm x 1400mm x 1440mm |
| Upper Die Plate |
100mm x 1250mm x 1450mm |
| Stroke |
1000(mm) |
| H.Y.D. Pressure |
100(kg/§²) |
| Control Pressure |
0.005~1,000(kg/§²) |
| |
| ITEM |
SPECIFICATION |
| Max. Pressure |
1.0/2.0/3.0/5.0(kg/§²) |
| Die Cooling |
Air/Water |
| Furnace Temp. |
600~800(¡É)(¡¾5¡É) |
| Furnace Capa |
AL 800kg(700¡É) |
|
ORDER & BACK-UP DATA
| ITEM |
SPECIFICATION |
| ORDERING |
999(ORDER) |
| CONTROL STEP |
20(STEP) |
| BACK UP-DATA |
Daily¡¤Monthly¡¤Yearly product quantity management, pressure data inquiry,
bad products¡¤no processing¡¤molding temperature management, total management
system
|
INDUCTION BILLET HEATER
FEATURE
The machine is a BILLET Heating System by induction heating, being used in the Forging Factory, the Rolling Mill and so on. These companies tend to substitute induction heating for heating with combustibles(fuel oil, gas) to prevent the pollution, to cut down the lavor, to control the quality and to reduce the running cost.
Heating with combustibles(fuel oil, gas etc.) is hard to achieve reasonable operations because it cause inaccurate
temperature control, difficult quality control, low heat efficiency, lots of scale by long heating time.
Finally the mold abrasion is being faster by the scale.
But Induction Heating removes those defects and provides high qualities as follows;
- With connected to a forging machine it is possible to set up the machine.
- Due to short heating time it preserves the plasticity of BILLET.
- It can heat BILLET uniformly and also can control simply any forging temperature in heating.
- It is suitable to mass-produce.
- Due to small quantity of scale, it can prevent mold from abrasion.
- Since there is no combustible, it dosen't cause any environmental pollution.
- The repair cost is cheapper than combustion furnace.
- With electrifing energy, it can cut down running cost.
- To keep worker's from electric shock, protective circuit is installed in the machine and since
there is no frame, there is no danger of raising fire.
TRANS/AXLE LOAD TESTER
SUMMARY
The equipment tests transmission of vehicle such as noise, gear ratio and shaft feeling automatically
in the assembling line.
SPECIFICATION
| ITEM |
SPECIFICATION |
ITEM |
SPECIFICATION |
| INPUT MOTOR |
440V 30(Kw) |
INPUT RPM |
4000(rpm) |
| OUTPUT MOTOR |
440V 285(Kw) |
Output RPM |
1370(rpm) |
| INPUT TORQUE |
32.0(Kgf¡¤M) |
CYCLE TIME |
180(Sec)/(ea) |
| OUTPUT TORQUE |
135.0(Kgf¡¤M) |
CONTROL TYPE |
TORQUE/RPM |
|
